redsn0w 0.9.6rc13 Tutorial

Unsure what jailbreak to use? Click here to find out.

If you would like, feel free to watch this tutorial in video form.

redsn0w is one of the original jailbreaking programs and is still going strong on it’s latest 0.9.6rc13 release. redsn0w is a simple to use jailbreak that should take just a few minutes from start to finish to complete that comes with the added benefit of supporting custom animated boot logos.

This is a fully untethered jailbreak for devices on iOS 4.3.2 meaning that unlike some other jailbreaks you can freely turn your device on and off without needing to rerun the program. As with all jailbreaks it is highly recommended that you connect your device to iTunes and let it sync to back up all of your data. You should not lose any data in the jailbreak but there’s always a chance that something could go wrong so it’s always a good idea to be safe.

To start with you will need to download redsn0w 0.9.6rc13 for either Windows or Mac.

redsn0w 0.9.6rc13 Windows Vista/7 Compatibility

redsn0w 0.9.6rc13 Windows Vista/7 Compatibility

These screenshots were taken using redsn0w 0.9.6b5 however the process remains the same in 0.9.6rc13

If you are on a Windows Vista or Windows 7 computer there is one additional step. Right click on redsn0w.exe and then click Properties. Select the Compatibility tab and here you’ll need to do two things. First check ‘Run this program in Compatibility mode’ for Windows XP Service Pack 3. If you don’t see an option for Service Pack 3 try Service Pack 2 or Windows 2000. Next check ‘Run this program as an Administrator’. Apply the changes and that’s it.

redsn0w 0.9.6rc13 Splash Screen

redsn0w 0.9.6rc13 Splash Screen

At this point you are going to need to locate the .IPSW firmware file for your device. If you are unsure where the firmware file is on your computer click here to learn how to find it. Once you have found the firmware direct redsn0w toward it and give it a moment to process.

redsn0w 0.9.6rc13 Options Select

redsn0w 0.9.6rc13 Options Select

At this point redsn0w will ask you to select your options. The most important thing is to keep the Install Cydia option checked, everything else is up to you. Not all options are available on all devices however so let me briefly explain what each does.

  • Install Cydia – Installs Cydia, the main package installer for jailbroken devices
  • Install custom bundle – Allows you to install a custom bundle
  • Allow boot animation – Allows you to install custom animated boot logos from Cydia
  • Enable battery percentage – Enables the numeric battery percentage
  • Just boot tethered right now – If you have a device that has a tethered jailbreak you will need to enable this to boot
  • Just enter pwned DFU mode right now – Allows you to immediately enter a pwned DFU mode state

Once you have selected the options you would like, click Next.

redsn0w 0.9.6rc13 DFU Mode Prepare

redsn0w 0.9.6rc13 DFU Mode Prepare

At this point you are ready to begin the jailbreak. Plug your device into the computer and then hold the Sleep button until you get ‘Slide to Power Off’. Shut off your device.

redsn0w 0.9.6rc13 DFU Mode Helper

redsn0w 0.9.6rc13 DFU Mode Helper

At this point you need to put your device into DFU mode. It’s a simple process and redsn0w will walk you through it. If you drop a button or mistime something just let your device boot normally and try again.

redsn0w 0.9.6rc13 Jailbreaking

redsn0w 0.9.6rc13 Jailbreaking

Once you successfully enter DFU mode then you’re all done, just sit back and let redsn0w finish up. Now just grab your device and you should see Cydia on your SpringBoard. Congratulations, you are now jailbroken!

Share